P0223: Throttle/Pedal Position Sensor/Switch 'B' Circuit High
P0223 means the engine computer is seeing a throttle or accelerator pedal position signal that is stuck too high on circuit B, so it can’t accurately control throttle response. The most common fix is repairing the wiring or replacing the throttle body or pedal sensor, usually about $150 to $450 at an independent shop.
- Severity
- High
- Can I drive?
- Drive with caution
- DIY?
- Possible with some experience
- Repair cost range
- $100 – $1,200
Get the answer for your exact car
Add your car and a few details. DashClue asks up to 3 questions, then tells you the most likely cause and what it should cost.
FreeNo card neededAnswer in about 2 minutes
What does P0223 mean?
This code points to a problem in the electronic throttle control or pedal position input, depending on how the vehicle is designed. The PCM expects circuit B to move through a normal voltage range, and when the signal stays too high it sets P0223 and may limit engine power. Common reasons include a bad sensor, damaged wiring, a poor connector, or corrosion in the harness. On many cars, the driver may notice reduced throttle response because the computer goes into fail-safe mode.
Common symptoms
- Check engine light on
- Lack of throttle response
- Hesitation when accelerating
- Reduced engine power or limp mode
- Rough idle
- Car may stall or surge
Causes, fixes and costs
P0223: Throttle/Pedal Position Sensor/Switch 'B' Circuit High
General guide for most cars. Your car may differ.
If the signal problem gets worse, the car may lose power, go into limp mode, or stall. Stop driving if the engine will not respond normally to the pedal, the check engine light starts flashing, or the car stalls in traffic.
Most likely causes
- 1
Faulty throttle position sensor or throttle bodyHigh
A stuck-high signal with poor throttle response, limp mode, or a code that returns right away often points to the throttle body sensor. If the throttle body is carboned up or the sensor inside it fails, the voltage may stay out of range.
Quick check: Inspect the throttle body connector and scan live data for an abnormal fixed voltage or percentage that does not change smoothly.
- 2
Bad accelerator pedal position sensorHigh
If the problem happens as soon as you press the pedal, or the pedal signal does not match the throttle signal, the pedal sensor may be failing. This is common when the car responds poorly but the throttle body itself looks clean.
Quick check: Use a scan tool to compare pedal sensor data with throttle sensor data while slowly pressing the pedal.
- 3
Damaged wiring or loose connector in circuit BMedium
Intermittent symptoms, a code that comes and goes, or other throttle codes often point to wiring issues. Heat, vibration, corrosion, or a pinched harness can make the voltage read too high.
Quick check: Wiggle-test the harness and inspect for bent pins, green corrosion, rubbed-through insulation, or water in the connector.
- 4
PCM or throttle adaptation issueLow
If sensors and wiring check out but the code remains, the control module may be misreading the circuit or need relearn/reset procedures after repairs. This is less common than a sensor or wiring fault.
Quick check: Clear the code and see if it returns after a throttle relearn; if not, the issue may have been calibration-related.
Can you fix it yourself?
Possible with some experience
Difficulty: Moderate. A careful DIYer can inspect connectors, wiring, and sometimes replace the pedal sensor or throttle body, but you need a scan tool to confirm the signal. If the vehicle needs throttle relearn procedures or wiring repair near the PCM, it is usually better handled by a shop.
Show the stepsHide the steps
- Check the battery voltage and make sure the terminals are clean and tight.
- Inspect the throttle body and accelerator pedal connectors for looseness or corrosion.
- Look over the harness for rubbing, cuts, or bent pins.
- Clear the code and watch live data for the pedal and throttle signals.
- Replace the failed sensor or throttle body if one signal is stuck high.
- Perform any required throttle relearn or idle relearn procedure.
- Road test and confirm the code does not return.
Estimated repair cost
$250 – $650
Throttle body assembly: parts and labor, common when the sensor is built into the throttle body
- Accelerator pedal position sensor$150 – $350
- Wiring repair or connector repair$120 – $300
- Throttle body cleaning and relearn$100 – $200
- PCM diagnosis or replacement$400 – $1,200
Prices vary by vehicle, parts quality, and how much electrical diagnosis is needed.
Frequently asked questions
Can I drive with code P0223?
Usually only for a short distance and with caution. If the car goes into limp mode, hesitates badly, or stalls, do not keep driving it.
Will P0223 clear itself?
Sometimes it may go away temporarily if the connection is intermittent, but the fault usually comes back until the sensor, wiring, or connector is fixed.
What is the most common fix for P0223?
The most common fix is repairing a damaged connector or replacing the failed throttle body or accelerator pedal sensor. A scan tool is usually needed to pinpoint which one is bad.
Can a dirty throttle body cause P0223?
Yes, heavy carbon buildup can sometimes affect throttle movement or sensor readings. Cleaning may help, but a stuck-high circuit usually means an electrical or sensor problem.
Will P0223 cause a failed inspection?
Yes, in many states a stored check engine light for P0223 will fail OBD emissions inspection. The code needs to be repaired and cleared before testing again.
Related codes
Related problems
This guide covers most cars and is general advice, not an inspection. Prices are typical US independent-shop ranges and vary by region, car and shop. If your brakes, steering or a warning light feel unsafe, stop driving and contact a mechanic.