P0120: Throttle/Pedal Position Sensor/Switch 'A' Circuit
P0120 means the engine computer is seeing a problem in the throttle or accelerator pedal position sensor circuit, which can confuse throttle control and affect how the engine responds. The most common fix is repairing wiring or replacing the throttle body or pedal position sensor, usually about $150 to $500 at an independent shop.
- Severity
- Moderate
- Can I drive?
- Drive with caution
- DIY?
- Possible with some experience
- Repair cost range
- $100 – $700
Get the answer for your exact car
Add your car and a few details. DashClue asks up to 3 questions, then tells you the most likely cause and what it should cost.
FreeNo card neededAnswer in about 2 minutes
What does P0120 mean?
The throttle position sensor or accelerator pedal position sensor tells the computer how far you are pressing the pedal or opening the throttle. The computer uses that signal to control fuel delivery, air flow, and sometimes electronic throttle operation. If the signal is missing, erratic, or out of range, the computer sets P0120. On many vehicles, this can trigger reduced power or poor throttle response.
Common symptoms
- Check engine light on
- Hesitation when accelerating
- Loss of power
- Rough idle
- Stalling at stop
- Poor throttle response
Causes, fixes and costs
P0120: Throttle/Pedal Position Sensor/Switch 'A' Circuit
General guide for most cars. Your car may differ.
The engine may go into reduced-power mode or respond unpredictably, which can make merging or passing unsafe. Stop driving if the engine stalls often, the throttle feels dead, or the vehicle will not accelerate normally.
Most likely causes
- 1
Damaged throttle or pedal sensor wiringHigh
Intermittent hesitation, sudden reduced power, or a check engine light that comes and goes often points to a wiring or connector issue. Wet connectors, rubbed-through wiring, or loose plugs are common clues.
Quick check: Inspect the connector and harness for corrosion, loose pins, broken lock tabs, or chafed wires near the throttle body or pedal assembly.
- 2
Faulty throttle position sensor or pedal position sensorHigh
A steady poor-throttle response, dead spots in pedal movement, or a code that returns after clearing can point to a bad sensor. This is more likely if wiring looks good and other related codes are not present.
Quick check: Use a scan tool with live data to watch the sensor signal while slowly pressing the pedal; look for sudden jumps, dropouts, or no change.
- 3
Dirty or failing electronic throttle bodyMedium
Rough idle, hesitation, or reduced power on drive-by-wire systems can happen when the throttle body motor or internal sensor fails. Carbon buildup alone usually causes driveability complaints, but the code often returns if the throttle unit is failing.
Quick check: Look for heavy carbon around the throttle plate and confirm whether the throttle plate moves smoothly with key-on commands if your scan tool supports it.
- 4
Computer or reference-voltage problemLow
If the signal, 5-volt reference, or ground is missing across multiple sensors, the fault may be in the harness or engine computer rather than the sensor itself. This is more likely if several unrelated codes appear together.
Quick check: Check for additional sensor codes and test the 5-volt reference and ground at the sensor connector with a multimeter.
Can you fix it yourself?
Possible with some experience
Difficulty: Moderate. Basic inspection and connector cleaning are reasonable for a careful DIY owner with a scan tool and multimeter. If the problem needs wiring repair, throttle body replacement, or circuit testing, ask the shop to diagnose the sensor signal, 5-volt reference, and ground before replacing parts.
Show the stepsHide the steps
- Check for loose, dirty, or damaged connectors at the throttle body or pedal sensor
- Inspect the harness for rubbed insulation, bent pins, or corrosion
- Clear the code and see if it returns right away
- Use live data to watch the throttle or pedal signal while moving it slowly
- Clean the throttle body only if contamination is visible and the vehicle uses an electronic throttle body that allows cleaning
- If wiring and cleaning do not help, test the sensor circuit with a multimeter or have a shop diagnose it
Estimated repair cost
$100 – $300
Wiring repair or connector replacement: small harness repair, terminals, or connector work
- Throttle position sensor or accelerator pedal sensor replacement$150 – $350
- Electronic throttle body replacement$300 – $700
- Throttle body cleaning and throttle relearn$100 – $200
- Engine computer diagnosis or repair$150 – $500
Prices vary by vehicle, engine layout, and local labor rates.
Frequently asked questions
Can I drive with code P0120?
Usually yes for a short time if the car still accelerates normally, but drive carefully. If the engine loses power, stalls, or the throttle feels unresponsive, stop driving and get it checked.
Will P0120 clear itself?
It may go away temporarily if the connection is intermittent, but the code usually returns until the fault is fixed. Clearing the code without repairing the cause is often only a short-term reset.
Is P0120 a throttle body problem or a pedal sensor problem?
It can be either, depending on the vehicle design. The code means the computer sees a problem in the throttle/pedal position sensor circuit, so the exact failed part has to be tested.
Can a dirty throttle body cause P0120?
Yes, on some electronic throttle systems a dirty throttle body can cause poor throttle movement or signal problems. But a wiring issue or a failing sensor is usually more likely than dirt alone.
How much does it cost to fix P0120?
Typical independent-shop repairs run about $150 to $500, but wiring damage or a throttle body replacement can cost more. The final price depends on whether the problem is the sensor, wiring, or throttle body assembly.
Related codes
Related problems
This guide covers most cars and is general advice, not an inspection. Prices are typical US independent-shop ranges and vary by region, car and shop. If your brakes, steering or a warning light feel unsafe, stop driving and contact a mechanic.