P0123: Throttle/Pedal Position Sensor/Switch 'A' Circuit High
P0123 means the engine computer is seeing an abnormally high voltage signal from the throttle or accelerator pedal position sensor circuit. The most common fix is repairing a damaged connector or replacing the throttle body or pedal position sensor, usually costing about $150 to $500 at an independent shop.
- Severity
- Moderate
- Can I drive?
- Drive with caution
- DIY?
- Possible with some experience
- Repair cost range
- $100 – $1,200
Get the answer for your exact car
Add your car and a few details. DashClue asks up to 3 questions, then tells you the most likely cause and what it should cost.
FreeNo card neededAnswer in about 2 minutes
What does P0123 mean?
This code points to a problem in the circuit that tells the engine computer how far the throttle is open or how far the accelerator pedal is pressed. On many cars, that signal comes from a throttle position sensor on the throttle body or a pedal position sensor at the accelerator pedal, depending on design. 'Circuit high' usually means the computer is seeing too much voltage, often from a wiring issue, bad sensor, or a connector problem. Because the computer uses this signal to control fuel delivery and throttle response, the car may go into reduced-power mode.
Common symptoms
- Check engine light on
- Poor throttle response
- Hesitation when accelerating
- Engine may go into limp mode
- Rough idle
- Higher idle speed than normal
Causes, fixes and costs
P0123: Throttle/Pedal Position Sensor/Switch 'A' Circuit High
General guide for most cars. Your car may differ.
The car may still drive, but it can lose power or respond unpredictably to the gas pedal. Stop driving if the engine will not rev normally, the car enters limp mode, or the throttle response becomes erratic.
Most likely causes
- 1
Faulty throttle position or pedal position sensorHigh
If the check engine light comes with poor throttle response or limp mode, the sensor itself may be sending a voltage that is too high. This is common when the code returns right away after clearing.
Quick check: Scan live data and watch the sensor voltage or percentage; a reading stuck high or jumping abnormally points to a bad sensor.
- 2
Damaged wiring or poor connector connectionHigh
Intermittent hesitation, sudden warning lights, or the code appearing after hitting a bump often point to wiring damage, corrosion, or a loose plug. A rubbed-through harness can raise the signal voltage or short it to power.
Quick check: Inspect the connector and wiring near the throttle body or pedal for bent pins, corrosion, broken insulation, or loose fit.
- 3
Throttle body problem or carbon buildupMedium
If idle is too high, throttle response is off, or the throttle plate sticks, the throttle body assembly may be at fault. Some vehicles use an integrated sensor that fails with the throttle body.
Quick check: Check for heavy carbon buildup or a throttle plate that does not move smoothly when commanded by scan tool.
- 4
PCM or accelerator pedal assembly faultLow
If the wiring and sensor tests are normal but the code keeps returning, the control module or pedal assembly may be failing. This is less common than sensor or wiring problems.
Quick check: Compare live data from both sensor tracks and follow factory test steps before replacing the module.
Can you fix it yourself?
Possible with some experience
Difficulty: Moderate. A basic inspection of the connector, wiring, and throttle body is doable for many owners with a scan tool and hand tools. If the sensor is built into the throttle body or the pedal assembly, ask the shop to diagnose live data and wiring before replacing parts.
Show the stepsHide the steps
- Read all codes and freeze-frame data
- Inspect the throttle body or pedal connector
- Look for bent pins, corrosion, or broken wires
- Check that the connector locks firmly in place
- Clear the code and test-drive if the problem was an obvious connection issue
- If the code returns, monitor live sensor data with a scan tool
- Replace the faulty sensor, throttle body, or pedal assembly only after testing
- Perform any required throttle relearn procedure
Estimated repair cost
$250 – $500
Throttle body replacement: parts and labor, common on vehicles with an integrated TPS
- Accelerator pedal position sensor or pedal assembly replacement$180 – $450
- Wiring repair or connector replacement$100 – $250
- Throttle body cleaning and relearn service$100 – $180
- PCM diagnosis or replacement$400 – $1,200
Prices vary by vehicle design, labor time, and local shop rates.
Frequently asked questions
Can I drive with code P0123?
Usually yes for a short distance, but drive gently because the car may lose throttle response or enter limp mode. If the engine will not respond normally to the gas pedal, stop driving.
Will P0123 clear itself?
It may go away temporarily if the connection is intermittent, but the problem usually comes back until the cause is fixed. Clearing the code without repair often does not solve it.
Is P0123 more likely the throttle body or the pedal?
Either one can cause it, depending on the car. A scan tool and wiring checks help determine whether the signal is coming from the throttle body sensor or the accelerator pedal sensor.
Can a dirty throttle body cause P0123?
Sometimes, especially if the throttle plate sticks or the assembly is worn. But a dirty throttle body is not as common a cause as a bad sensor or wiring issue for this code.
Will P0123 pass inspection?
Usually not if the check engine light is on, because the vehicle has an active emissions fault. Even if it runs okay, the code should be repaired before inspection.
Related codes
Related problems
This guide covers most cars and is general advice, not an inspection. Prices are typical US independent-shop ranges and vary by region, car and shop. If your brakes, steering or a warning light feel unsafe, stop driving and contact a mechanic.