P0220: Throttle/Pedal Position Sensor/Switch 'B' Circuit

P0220 means the engine computer sees a problem in the throttle or accelerator pedal position sensor/switch 'B' circuit, so it cannot trust throttle input. The most common fix is replacing the throttle body or accelerator pedal position sensor and repairing any wiring issues, which usually costs about $200 to $600 at an independent shop.

Severity
High
Can I drive?
Drive with caution
DIY?
Possible with some experience
Repair cost range
$100 – $1,200

Get the answer for your exact car

Add your car and a few details. DashClue asks up to 3 questions, then tells you the most likely cause and what it should cost.

FreeNo card neededAnswer in about 2 minutes

What does P0220 mean?

This code points to an electrical problem in the throttle control system, not just a dirty throttle body. The engine computer uses throttle or pedal position signals to control fuel, air, and throttle response, so a bad signal can cause poor drivability or a limp mode. The problem may be inside the sensor itself, in the wiring, or in the connector. On many cars, a damaged throttle body assembly or accelerator pedal sensor is the real cause.

Common symptoms

  • Check engine light on
  • Reduced engine power
  • Slow throttle response
  • Limp mode
  • Rough idle
  • Hesitation when accelerating

Causes, fixes and costs

DashClue diagnosis

P0220: Throttle/Pedal Position Sensor/Switch 'B' Circuit

General guide for most cars. Your car may differ.

Severity: HighDrive with caution

The car may go into reduced-power mode or respond unpredictably to the gas pedal, which can make merging or passing unsafe. Stop driving if the engine loses power suddenly, the pedal stops responding normally, or the car will not keep normal idle speed.

Most likely causes

  1. 1

    Faulty throttle body or throttle position sensorHigh

    A failing throttle body often causes reduced power, hesitation, or a stuck limp mode, especially if the light stays on and the throttle feels inconsistent.

    Quick check: Scan for throttle-related codes and inspect live throttle position data while pressing the pedal slowly.

  2. 2

    Bad accelerator pedal position sensorMedium

    If the code appears with poor pedal response but the throttle body looks clean and there are no airflow issues, the pedal sensor is a strong suspect.

    Quick check: Compare pedal position data from both sensor tracks with a scan tool and look for drops or mismatch.

  3. 3

    Wiring or connector problem in the circuitMedium

    Intermittent symptoms, codes that come and go, or problems after hitting bumps often point to a loose connector, damaged wire, or corrosion.

    Quick check: Inspect the harness and connectors for broken wires, bent pins, moisture, or corrosion and wiggle-test the harness while watching live data.

  4. 4

    PCM or calibration issueLow

    If the sensor and wiring test good but the code returns, the control module or its software may be misreading the signal.

    Quick check: Check for software updates and verify power, ground, and reference voltage before suspecting the module.

Can you fix it yourself?

Possible with some experience

Difficulty: Moderate. A careful DIYer can inspect connectors, wiring, and sometimes replace the throttle body or pedal sensor with basic hand tools and a scan tool. You should confirm the exact component with live data first, because many vehicles need a throttle relearn or idle relearn after repair.

Show the steps
  1. Read all stored and pending codes.
  2. Inspect the throttle body, pedal sensor connector, and wiring for damage or corrosion.
  3. Check live data for smooth, matching sensor signals.
  4. Repair loose pins, damaged wiring, or bad connectors.
  5. Replace the throttle body or pedal sensor if testing points to it.
  6. Clear the codes.
  7. Perform any relearn or calibration procedure required by the vehicle.
  8. Road test and recheck for returning codes.

Estimated repair cost

$250 – $650

Throttle body assembly: parts and labor, plus relearn if needed

  • Accelerator pedal position sensor$180 – $450
  • Wiring repair or connector repair$100 – $300
  • Throttle body cleaning and relearn$100 – $180
  • PCM diagnosis or replacement/programming$250 – $1,200

Prices vary by vehicle, labor rate, and whether a relearn or programming step is required.

Frequently asked questions

Can I drive with P0220?

Usually yes for a short distance if the car still drives normally, but use caution because it may lose throttle response or enter limp mode. If the car barely accelerates or idles poorly, avoid driving it.

Will P0220 clear itself?

It may clear temporarily if the connection issue is intermittent, but the fault usually comes back if the underlying problem is still there. Permanent repair is needed to keep it from returning.

Is P0220 a throttle body code or pedal sensor code?

It can be either, because the code refers to the 'B' circuit in the throttle/pedal position system. The exact failed part depends on the vehicle design and the test results.

Can a dirty throttle body cause P0220?

Sometimes, but electrical faults are more common than simple dirt for this code. Cleaning alone will not fix a bad sensor, broken wire, or connector issue.

Will this code fail an inspection?

In many states, a check engine light with an active P0220 will fail emissions inspection. The car usually needs the code repaired and the monitors set before it can pass.

Related codes

  • P0120 Throttle/Pedal Position Sensor/Switch 'A' Circuit
  • P0121 Throttle/Pedal Position Sensor/Switch 'A' Circuit Range/Performance
  • P0122 Throttle/Pedal Position Sensor/Switch 'A' Circuit Low
  • P0123 Throttle/Pedal Position Sensor/Switch 'A' Circuit High

Related problems

This guide covers most cars and is general advice, not an inspection. Prices are typical US independent-shop ranges and vary by region, car and shop. If your brakes, steering or a warning light feel unsafe, stop driving and contact a mechanic.