P0111: Intake Air Temperature Sensor 1 Circuit Range/Performance
P0111 means the engine computer is seeing an intake air temperature sensor signal that does not make sense for the conditions. The most common fix is replacing the intake air temperature sensor or repairing its wiring, usually about $100 to $300 at an independent shop.
- Severity
- Moderate
- Can I drive?
- Drive with caution
- DIY?
- Possible with some experience
- Repair cost range
- $80 – $500
Get the answer for your exact car
Add your car and a few details. DashClue asks up to 3 questions, then tells you the most likely cause and what it should cost.
FreeNo card neededAnswer in about 2 minutes
What does P0111 mean?
The intake air temperature (IAT) sensor tells the engine computer how warm the air entering the engine is. The computer uses that information to adjust fuel delivery and ignition timing so the engine runs smoothly and efficiently. When the signal is out of range or changes in a way that does not match the engine’s actual conditions, the computer sets P0111. This can happen from a bad sensor, wiring problem, connector issue, or sometimes an air intake problem that makes the reading inaccurate.
Common symptoms
- Check engine light on
- Rough idle
- Hesitation when accelerating
- Poor fuel economy
- Hard starting in some cases
- Stale or overly rich running smell
Causes, fixes and costs
P0111: Intake Air Temperature Sensor 1 Circuit Range/Performance
General guide for most cars. Your car may differ.
This code usually will not leave you stranded right away, but the engine may run too rich or too lean, which can hurt drivability and fuel economy. Stop driving if the engine runs very rough, stalls, or the check engine light starts flashing.
Most likely causes
- 1
Bad intake air temperature sensorHigh
A sensor that reads too high, too low, or changes erratically is the most common reason for P0111. Rough idle, hesitation, and no other obvious intake problems often point here.
Quick check: Look at live data with a scan tool; if the IAT reading is far outside outside temperature or jumps around, the sensor may be bad.
- 2
Damaged wiring or loose connectorHigh
Broken wires, corrosion, or a poor connector fit can make the signal unstable and trigger a range/performance code. Intermittent symptoms or a code that returns after bumps or rain often point to this.
Quick check: Inspect the harness and connector for corrosion, bent pins, broken insulation, or loose fit and gently wiggle the connector while watching live data.
- 3
Dirty, restricted, or modified air intake pathMedium
If the sensor is mounted in a hot spot, blocked by debris, or affected by an aftermarket intake or missing ducting, the reading may not match actual air temperature. This is more likely when the problem started after air filter or intake work.
Quick check: Verify the air box, ducting, and filter are installed correctly and that the sensor is in the proper location.
- 4
Faulty engine computer input circuitLow
If the sensor and wiring test good but the scan data is still wrong, the PCM circuit itself may be failing. This is less common and usually comes after other causes are ruled out.
Quick check: Have a shop test the sensor circuit for proper voltage and resistance before suspecting the computer.
Can you fix it yourself?
Possible with some experience
Difficulty: Moderate. A careful owner can inspect the sensor and connector, clean the connection, and replace the IAT sensor if it is easy to access. You will need a basic scan tool, multimeter, and the correct replacement sensor if testing shows the sensor is faulty.
Show the stepsHide the steps
- Read the code and check live IAT temperature data
- Compare the IAT reading to outside air temperature after the car sits overnight
- Inspect the sensor, intake tube, and wiring connector for damage or looseness
- Repair any damaged wiring or dirty terminals
- Replace the IAT sensor if the reading is still out of range
- Clear the code and road test the car
- Recheck live data to confirm the reading is stable
Estimated repair cost
$100 – $300
Intake air temperature sensor replacement: parts about $20-$80, labor about $80-$220
- Wiring repair or connector replacement$120 – $350
- Air intake duct, air box, or connector repair$80 – $250
- PCM diagnostic and circuit repair$150 – $500
Prices vary by vehicle design, rust, and local labor rates, and diagnostics may be separate from repair.
Frequently asked questions
Can I drive with P0111?
Usually yes for short trips, but drive gently and get it checked soon. If the engine starts running very rough, stalls, or loses power badly, stop driving and have it towed.
Will P0111 cause bad gas mileage?
Yes, it can. When the engine computer gets a bad air temperature reading, it may add too much or too little fuel.
Can I fix P0111 myself?
Sometimes. If the problem is a loose connector, damaged wire, or an easy-to-reach sensor, a DIY repair is possible with basic tools and a scan tool.
Will P0111 fail emissions or inspection?
It can, because the check engine light is on and the engine computer has a fault stored. Some states will also fail the car if readiness monitors are not set after repairs.
Is P0111 the same as a mass air flow sensor code?
No. P0111 is for the intake air temperature sensor signal range or performance, although on some vehicles the IAT reading may be part of another sensor assembly.
Related codes
Related problems
This guide covers most cars and is general advice, not an inspection. Prices are typical US independent-shop ranges and vary by region, car and shop. If your brakes, steering or a warning light feel unsafe, stop driving and contact a mechanic.