P0110: Intake Air Temperature Sensor 1 Circuit

P0110 means the engine computer sees a problem in the intake air temperature (IAT) sensor circuit, which tells it how warm the incoming air is. The most common fixes are repairing damaged wiring or replacing the IAT sensor, typically costing about $120 to $350 at an independent shop.

Severity
Moderate
Can I drive?
Drive with caution
DIY?
Possible with some experience
Repair cost range
$80 – $550

Get the answer for your exact car

Add your car and a few details. DashClue asks up to 3 questions, then tells you the most likely cause and what it should cost.

FreeNo card neededAnswer in about 2 minutes

What does P0110 mean?

The intake air temperature sensor helps the engine computer adjust fuel delivery and ignition timing based on the temperature of the air entering the engine. If the signal is missing, shorted, or out of range, the computer cannot accurately calculate the air density. That can cause a hard start, rough idle, poor fuel economy, or an illuminated check engine light. On many vehicles the IAT sensor is built into the MAF sensor, while on others it is a separate sensor in the intake tract.

Common symptoms

  • Check engine light on
  • Rough idle
  • Hard starting
  • Poor fuel economy
  • Hesitation on acceleration
  • May run rich or lean

Causes, fixes and costs

DashClue diagnosis

P0110: Intake Air Temperature Sensor 1 Circuit

General guide for most cars. Your car may differ.

Severity: ModerateDrive with caution

Most cars can still be driven short term, but the engine may run too rich or too lean and fuel economy can suffer. Stop driving if the engine starts stalling, runs very rough, or shows other severe drivability problems.

Most likely causes

  1. 1

    Bad IAT sensorHigh

    A failed sensor often causes a steady check engine light, poor fuel economy, or rough running with no obvious wiring damage. This is more likely if live data shows an impossible temperature reading like -40°F or extremely high heat.

    Quick check: Read live scan data and compare the IAT reading to outdoor air temperature after the car sits overnight.

  2. 2

    Damaged wiring or connectorHigh

    Intermittent symptoms, a code that returns after hitting bumps, or a reading that changes when the harness is moved point to wiring trouble. Corrosion, broken wires, or loose terminals are common near the air intake and engine cover.

    Quick check: Inspect the connector for bent pins, corrosion, loose fit, or rubbed-through wiring, then wiggle-test the harness while watching live data.

  3. 3

    Dirty or faulty MAF assembly with built-in IATMedium

    If the IAT is part of the mass air flow sensor, a MAF problem can trigger this code along with airflow-related driveability complaints. This is more likely if the vehicle also has lean codes or airflow-related symptoms.

    Quick check: Check whether the IAT is separate or built into the MAF, and inspect the MAF for contamination or prior improper cleaning.

  4. 4

    Blown sensor circuit fuse or power/ground issueLow

    A missing reference voltage or ground can set P0110 and usually shows up as a dead or fixed temperature reading. This is more likely if multiple engine sensor codes appear at the same time.

    Quick check: Verify the sensor has the correct reference voltage and ground with a multimeter or wiring diagram.

Can you fix it yourself?

Possible with some experience

Difficulty: Moderate. If the IAT is a separate sensor and the issue is an unplugged connector or damaged pigtail, this can be a doable home repair with basic hand tools, a scan tool, and possibly a multimeter. If the sensor is built into the MAF or the wiring is hard to access, a shop diagnosis is often faster and safer.

Show the steps
  1. Check the intake sensor location and whether it is separate or part of the MAF
  2. Inspect the connector and wiring for damage, oil, dirt, or corrosion
  3. Compare live IAT data to outside air temperature after the car sits
  4. Clear the code and see whether it returns immediately
  5. Replace the sensor or repair the connector if the reading is clearly wrong
  6. Repair any damaged wiring and secure the harness away from heat and movement

Estimated repair cost

$80 – $220

Replace intake air temperature sensor: parts about $20-$90, labor about $60-$130

  • Repair sensor wiring or connector$120 – $350
  • Replace mass air flow sensor with built-in IAT$250 – $550
  • Diagnose power, ground, or PCM circuit fault$120 – $220

Prices vary by vehicle, engine layout, and local labor rates, and dealer pricing is often higher.

Frequently asked questions

Can I drive with P0110?

Usually yes for a short time, but the engine may run poorly and waste fuel. Get it checked soon, especially if the idle gets rough or the car starts stalling.

Will P0110 clear itself?

Sometimes it may disappear if the problem was temporary, but the code usually returns if the sensor or wiring is actually bad. Clearing it without fixing the cause does not solve the issue.

Is P0110 the same as a bad MAF sensor?

Not always. On some cars the IAT sensor is built into the MAF sensor, but on others it is a separate part and the MAF may be fine.

Can a dirty air filter cause P0110?

A dirty air filter usually does not directly set this code, but it can contribute to airflow issues on vehicles with the IAT built into the MAF housing. The sensor and wiring should still be checked first.

Will P0110 fail an emissions test?

It can, because the check engine light is on and the engine may not be managing fuel correctly. Most states will fail a vehicle with an active emissions-related code.

Related codes

  • P0100 Mass Or Volume Air Flow Circuit
  • P0101 Mass or Volume Air Flow Circuit Range/Performance
  • P0111 Intake Air Temperature Sensor 1 Circuit Range/Performance
  • P0112 Intake Air Temperature Sensor 1 Circuit Low
  • P0113 Intake Air Temperature Sensor 1 Circuit High
  • P0102 Mass or Volume Air Flow Circuit Low Input

Related problems

This guide covers most cars and is general advice, not an inspection. Prices are typical US independent-shop ranges and vary by region, car and shop. If your brakes, steering or a warning light feel unsafe, stop driving and contact a mechanic.