P0102: Mass or Volume Air Flow Circuit Low Input

P0102 means the engine computer is seeing a mass air flow (MAF) signal that is lower than expected, so it may not be able to meter fuel correctly. The most common fix is cleaning or replacing the MAF sensor and checking its wiring, usually about $120 to $350 at an independent shop.

Severity
Moderate
Can I drive?
Drive with caution
DIY?
Possible with some experience
Repair cost range
$40 – $400

Get the answer for your exact car

Add your car and a few details. DashClue asks up to 3 questions, then tells you the most likely cause and what it should cost.

FreeNo card neededAnswer in about 2 minutes

What does P0102 mean?

The mass air flow sensor measures how much air is entering the engine so the computer can add the right amount of fuel. When the signal is too low, the computer may think less air is coming in than really is, which can make the engine run too rich or too lean depending on the situation. This code can be caused by a dirty or failing MAF sensor, wiring problems, or an air intake issue that affects the sensor reading. It often comes with drivability problems like rough idle, hesitation, or poor fuel economy.

Common symptoms

  • Check engine light on
  • Rough idle
  • Hesitation when accelerating
  • Loss of power
  • Bad fuel mileage
  • Stalling at stop

Causes, fixes and costs

DashClue diagnosis

P0102: Mass or Volume Air Flow Circuit Low Input

General guide for most cars. Your car may differ.

Severity: ModerateDrive with caution

The car may still run, but fuel control can be off enough to cause stalling, hesitation, or poor acceleration. Stop driving if the engine stalls often, runs very rough, or the check engine light starts flashing.

Most likely causes

  1. 1

    Dirty or failing MAF sensorHigh

    A weak MAF signal often shows up with rough idle, hesitation, or reduced power, especially after an air filter change or high-mileage use. If unplugging the sensor briefly changes how the engine runs, that points toward the sensor or its circuit.

    Quick check: Inspect the sensor for dirt or oil contamination and try a proper MAF sensor cleaner if it is visibly dirty.

  2. 2

    Damaged MAF wiring or connectorHigh

    A low-input code with an intermittent stumble, bucking, or a code that returns after hitting bumps often points to wiring or connector trouble. Corrosion, loose pins, or rubbed-through wiring can drop the sensor signal.

    Quick check: Inspect the connector, pins, and harness near the air intake for damage, corrosion, or loose fit.

  3. 3

    Air leak before or after the MAF sensorMedium

    Vacuum leaks or a loose intake tube can confuse airflow readings and lead to rough idle or lean-related symptoms along with P0102. If the intake hose is cracked or clamps are loose, the airflow signal may not match engine demand.

    Quick check: Look for split intake boots, loose clamps, disconnected hoses, or unmetered air leaks between the air filter box and throttle body.

  4. 4

    Restricted air filter or intake blockageLow

    A badly clogged air filter or blocked intake can reduce airflow and contribute to a low reading, especially if the engine also feels sluggish. This is more likely if maintenance has been ignored.

    Quick check: Check the air filter and intake ducting for heavy dirt, collapse, or blockage.

Can you fix it yourself?

Possible with some experience

Difficulty: Moderate. Basic owners can inspect the air filter, intake tube, and MAF connector, and sometimes clean the sensor with MAF-safe cleaner. If wiring tests or live-data checks are needed, a shop or experienced DIYer with a scan tool and multimeter is better.

Show the steps
  1. Check the air filter and intake tube for dirt, cracks, or loose clamps
  2. Inspect the MAF connector and wiring for corrosion or damage
  3. Clean the MAF sensor only with MAF sensor cleaner
  4. Clear the code and road test the car
  5. If the code returns, test the sensor signal and power/ground circuits
  6. Repair damaged wiring or replace the MAF sensor if tests fail

Estimated repair cost

$75 – $150

Clean mass air flow sensor: labor plus cleaner, often a quick diagnostic service

  • Replace mass air flow sensor$150 – $400
  • Repair MAF wiring or connector$120 – $350
  • Replace air intake boot or duct$80 – $220
  • Replace air filter and inspect intake system$40 – $120

Prices vary by vehicle, labor rate, and whether the fault is the sensor itself or the wiring around it.

Frequently asked questions

Can I drive with P0102?

Usually yes for a short time, but the car may run poorly and use more fuel. If it stalls, hesitates badly, or the check engine light flashes, stop driving and have it checked.

Will cleaning the MAF sensor fix P0102?

Sometimes. If the sensor is dirty or contaminated, proper cleaning can clear the problem, but a bad sensor or wiring fault will need repair.

Can a bad air filter cause P0102?

Yes, if the filter is badly clogged or the intake system is restricted. It is not the most common cause, but it is easy to check first.

Will P0102 cause a rough idle?

It can. The engine computer may miscalculate airflow and fuel delivery, which often causes rough idle, hesitation, or stalling at stops.

Does P0102 mean I need a new MAF sensor?

Not always. Wiring damage, loose connectors, intake leaks, or a dirty sensor can all trigger the code, so the sensor should be tested before replacing it.

Related codes

  • P0100 Mass Or Volume Air Flow Circuit
  • P0101 Mass or Volume Air Flow Circuit Range/Performance
  • P0103 Mass Or Volume Air Flow Circuit High Input
  • P0171 System Too Lean (Bank 1)
  • P0174 System Too Lean (Bank 2)
  • P0113 Intake Air Temperature Sensor 1 Circuit High

Related problems

This guide covers most cars and is general advice, not an inspection. Prices are typical US independent-shop ranges and vary by region, car and shop. If your brakes, steering or a warning light feel unsafe, stop driving and contact a mechanic.