P0107: Manifold Absolute Pressure/Barometric Pressure Circuit Low Input

P0107 means the engine computer is seeing a MAP or barometric pressure signal that is lower than expected, which can throw off fueling and cause rough running or hard starting. The most common fix is repairing a bad MAP sensor, damaged wiring, or a loose connector, usually costing about $120 to $350 at an independent shop.

Severity
Moderate
Can I drive?
Drive with caution
DIY?
Possible with some experience
Repair cost range
$75 – $1,200

Get the answer for your exact car

Add your car and a few details. DashClue asks up to 3 questions, then tells you the most likely cause and what it should cost.

FreeNo card neededAnswer in about 2 minutes

What does P0107 mean?

The MAP sensor helps the computer figure out engine load by reading intake manifold pressure, and on some cars the same circuit is also used for barometric pressure. If the signal voltage stays too low, the computer thinks the engine has a different air pressure condition than it really does. That can make the fuel mixture too rich or too lean, depending on the situation. The problem is often caused by a failed sensor, a wiring issue, or a vacuum problem on engines that use a vacuum hose to the sensor.

Common symptoms

  • Check engine light on
  • Rough idle
  • Hesitation when accelerating
  • Hard starting
  • Stalling at stop
  • Bad gas mileage

Causes, fixes and costs

DashClue diagnosis

P0107: Manifold Absolute Pressure/Barometric Pressure Circuit Low Input

General guide for most cars. Your car may differ.

Severity: ModerateDrive with caution

The car may run poorly, stall, or use too much fuel if the problem is ignored. Stop driving if the engine stalls repeatedly, runs extremely rough, or the check engine light starts flashing.

Most likely causes

  1. 1

    Failed MAP sensorHigh

    Most likely when the engine runs poorly, hesitates, or idles rough and the code comes back right away. A dead or weak sensor can send a voltage that is stuck too low.

    Quick check: Inspect the sensor data on a scan tool; if the reading is near zero or does not change with engine load, the sensor may be bad.

  2. 2

    Damaged wiring or poor connector at MAP sensorHigh

    Very common if the code appears intermittently, especially after bumps, rain, or engine movement. Corrosion, broken wires, or loose terminals can pull the signal voltage low.

    Quick check: Look for loose plugs, bent pins, rubbed-through wiring, oil intrusion, or corrosion at the sensor connector.

  3. 3

    Vacuum hose leak or disconnected hose to sensorMedium

    This applies on vehicles that use a vacuum hose to the MAP sensor. A split, disconnected, or blocked hose can give the sensor the wrong pressure signal and cause rough idle or hesitation.

    Quick check: Follow the hose from the sensor and make sure it is connected, not cracked, and not plugged by debris.

  4. 4

    Low reference voltage or PCM issueLow

    More likely if the sensor and wiring test good but the signal still reads low. This is less common and may show up with other sensor codes too.

    Quick check: Verify the sensor has proper 5-volt reference and ground before replacing the PCM.

Can you fix it yourself?

Possible with some experience

Difficulty: Moderate. A handy owner can inspect the connector, wiring, and any vacuum hose, and sometimes replace the MAP sensor with basic hand tools. You need a scan tool or multimeter to confirm the sensor signal and make sure the wiring is not the real problem.

Show the steps
  1. Read the code and record freeze-frame data
  2. Inspect the MAP sensor connector and wiring
  3. Check for a loose, cracked, or disconnected vacuum hose if equipped
  4. Clean corrosion from the connector if present
  5. Verify 5-volt reference and ground with a multimeter
  6. Replace the MAP sensor if readings are clearly wrong
  7. Clear the code and road test

Estimated repair cost

$120 – $350

MAP sensor replacement: parts ~$30-$120, labor ~$90-$230

  • Wiring repair or connector service$100 – $250
  • Vacuum hose replacement or repair$75 – $180
  • PCM diagnosis and replacement$400 – $1,200

Actual prices vary by vehicle, engine layout, and local labor rates.

Frequently asked questions

Can I drive with P0107?

Usually yes for short trips, but drive gently and get it checked soon. If the engine stalls, runs very rough, or loses power badly, stop driving.

Will P0107 cause bad gas mileage?

Yes, it can. A wrong MAP signal can make the engine run too rich or too lean, which often hurts fuel economy.

Can a dirty air filter cause P0107?

Not usually by itself. A dirty air filter may affect performance, but P0107 is more often caused by the sensor, wiring, or a vacuum hose problem.

Do I need a new MAP sensor for P0107?

Not always. Many cases are caused by a loose connector, damaged wiring, or a hose problem, so testing is better than replacing parts first.

Will P0107 pass inspection?

In many states, a check engine light means it will fail emissions inspection. The code should be repaired and cleared before testing.

Related codes

  • P0100 Mass Or Volume Air Flow Circuit
  • P0101 Mass or Volume Air Flow Circuit Range/Performance
  • P0102 Mass or Volume Air Flow Circuit Low Input
  • P0106 Manifold Absolute Pressure/Barometric Pressure Circuit Range/Performance
  • P0108 Manifold Absolute Pressure/Barometric Pressure Circuit High Input
  • P0113 Intake Air Temperature Sensor 1 Circuit High

Related problems

This guide covers most cars and is general advice, not an inspection. Prices are typical US independent-shop ranges and vary by region, car and shop. If your brakes, steering or a warning light feel unsafe, stop driving and contact a mechanic.