P0201: Injector Circuit/Open - Cylinder 1
P0201 means the engine computer is not seeing the proper electrical signal from the fuel injector on cylinder 1. The most common fix is repairing the injector wiring or replacing a bad injector, usually costing about $150 to $450 at an independent shop.
- Severity
- Moderate
- Can I drive?
- Drive with caution
- DIY?
- Possible with some experience
- Repair cost range
- $20 – $900
Get the answer for your exact car
Add your car and a few details. DashClue asks up to 3 questions, then tells you the most likely cause and what it should cost.
FreeNo card neededAnswer in about 2 minutes
What does P0201 mean?
The fuel injector for cylinder 1 sprays fuel into that cylinder when the engine computer tells it to. If the circuit is open, the injector may not fire at all, so that cylinder can run lean or misfire. This code can be caused by a bad injector, damaged wiring, a loose connector, or a problem in the engine computer’s control circuit. On many cars, the engine may run rough, set a misfire code, or lose power if cylinder 1 is not getting fuel correctly.
Common symptoms
- Check engine light on
- Rough idle
- Engine misfire
- Loss of power when accelerating
- Hard starting
- Bad gas mileage
Causes, fixes and costs
P0201: Injector Circuit/Open - Cylinder 1
General guide for most cars. Your car may differ.
If cylinder 1 is not getting fuel, the engine may misfire, run poorly, and damage the catalytic converter if driven for long periods. Stop driving if the check engine light starts flashing, the engine is shaking badly, or the car stalls.
Most likely causes
- 1
Damaged injector wiring or connectorHigh
A loose plug, broken wire, corrosion, or rubbed-through harness is the most common cause when the code appears with a rough idle, misfire, or intermittent stalling.
Quick check: Inspect the wiring and connector at cylinder 1 injector for looseness, bent pins, corrosion, or damaged insulation; wiggle-test the harness with the engine idling if safe.
- 2
Failed fuel injector on cylinder 1High
A bad injector coil can create an open circuit and often goes with a cylinder 1 misfire, rough running, or a no-start if the injector is completely dead.
Quick check: Measure injector resistance and compare it with the other injectors, or swap the injector with another cylinder if the engine design allows it.
- 3
Blown injector fuse or power supply issueMedium
If multiple injectors share power and the injector has no voltage, the code may appear with a no-start or several misfire symptoms.
Quick check: Check injector fuses and verify battery voltage at the injector connector with the key on.
- 4
PCM driver problemLow
If the injector, wiring, and power feed test good but cylinder 1 still has no injector pulse, the engine computer driver may be faulty.
Quick check: Use a noid light or scan tool to confirm injector command; if command is missing with good wiring, a shop should test the PCM output.
Can you fix it yourself?
Possible with some experience
Difficulty: Moderate. Basic electrical tools help here: a digital multimeter, inspection light, and possibly a noid light. Start with the connector and wiring at cylinder 1; if the injector itself is bad or the PCM is suspected, diagnosis is better left to a shop.
Show the stepsHide the steps
- Inspect the cylinder 1 injector connector for a loose fit, corrosion, or broken lock tab.
- Check the harness for cuts, melted insulation, or rubbing near the engine.
- Verify injector fuse(s) and power at the injector with the key on.
- Compare injector resistance to the other cylinders if you have a multimeter.
- Clear the code and see if it returns after a short drive.
- If the wiring is good and the injector tests open, replace the injector.
- If the injector is good but there is no control signal, have the PCM circuit tested.
Estimated repair cost
$100 – $300
Repair injector wiring or connector: parts usually low; labor varies with access
- Replace fuel injector on cylinder 1$150 – $450
- Replace injector fuse or relay$20 – $120
- PCM driver diagnosis and repair$150 – $900
Prices vary by vehicle, engine layout, and local labor rates.
Frequently asked questions
Can I drive with P0201?
Usually yes for a short trip, but drive gently and get it checked soon. If the engine is shaking hard, stalling, or the check engine light is flashing, stop driving.
Will P0201 cause a misfire?
Yes. If cylinder 1 injector is not working, that cylinder can misfire or run lean.
Can a bad injector wiring cause this code?
Yes. An open circuit, loose connector, or damaged wire is one of the most common causes.
How much does it cost to fix P0201?
Typical independent-shop repair costs are about $150 to $450, but a wiring repair or PCM-related diagnosis can cost more.
Can I fix P0201 myself?
You may be able to if the problem is a loose connector, damaged wire, or an easy-to-reach injector. If testing points to the PCM or the diagnosis is unclear, a shop is the better choice.
Related codes
Related problems
This guide covers most cars and is general advice, not an inspection. Prices are typical US independent-shop ranges and vary by region, car and shop. If your brakes, steering or a warning light feel unsafe, stop driving and contact a mechanic.