P0155: O2 Sensor Heater Circuit (Bank 2 Sensor 1)
P0155 means the engine computer has found a problem in the heater circuit for the upstream oxygen sensor on bank 2. The most common fix is replacing a failed O2 sensor or repairing damaged heater wiring, which usually costs about $150 to $350 at an independent shop.
- Severity
- Moderate
- Can I drive?
- Drive with caution
- DIY?
- Possible with some experience
- Repair cost range
- $20 – $400
Get the answer for your exact car
Add your car and a few details. DashClue asks up to 3 questions, then tells you the most likely cause and what it should cost.
FreeNo card neededAnswer in about 2 minutes
What does P0155 mean?
The oxygen sensor measures exhaust oxygen so the engine computer can adjust fuel mixture. Sensor 1 on bank 2 is the upstream sensor on the side of the engine without cylinder 1, and its built-in heater helps it warm up quickly after a cold start. If the heater circuit fails, the sensor may take too long to start working, which can hurt fuel control and emissions. This code is usually caused by a bad sensor heater, wiring damage, or a blown fuse in the heater circuit.
Common symptoms
- Check engine light on
- Rough running when cold
- Bad gas mileage
- Failed emissions test
- Longer warm-up before closed-loop operation
Causes, fixes and costs
P0155: O2 Sensor Heater Circuit (Bank 2 Sensor 1)
General guide for most cars. Your car may differ.
The car will usually still run, but fuel mixture control may be poorer until the sensor warms up. If you also notice a strong fuel smell, rough running, or other driveability problems, get it checked soon.
Most likely causes
- 1
Failed oxygen sensor heaterHigh
This is most likely if the code returns by itself, especially with a normal-running engine and no obvious wiring damage. A worn sensor heater often fails after high mileage or age.
Quick check: Inspect the sensor age and heater resistance if you have a multimeter; many shops confirm by testing the sensor and comparing live data on cold start.
- 2
Damaged heater wiring or connectorMedium
More likely if the code appears after recent exhaust work, road debris damage, or if the light comes and goes over bumps. Melted insulation, corrosion, or a loose plug can interrupt the heater circuit.
Quick check: Look for broken, stretched, melted, or corroded wires and a loose connector near the exhaust pipe.
- 3
Blown fuse or power supply problemMedium
This is more likely if another sensor heater code is present or the code set right after a short circuit. A heater circuit that has no power will stop the sensor from warming up.
Quick check: Check the fuse related to oxygen sensor heaters and verify power at the connector with the key on, using the vehicle wiring diagram.
- 4
Faulty engine control circuitLow
This is less common and usually considered after the sensor, wiring, and fuse all test good. It may show up as a persistent code that will not clear even after repairs.
Quick check: A shop can command the circuit and test control side operation before condemning the PCM.
Can you fix it yourself?
Possible with some experience
Difficulty: Moderate. A DIY repair is possible if the problem is a damaged connector, blown fuse, or sensor replacement. You will need basic hand tools, a scan tool helps, and the correct upstream bank 2 sensor for the vehicle.
Show the stepsHide the steps
- Verify the code and check for related heater codes
- Inspect the bank 2 sensor 1 wiring and connector for heat damage or corrosion
- Check the fuse for oxygen sensor heaters
- Test sensor heater power and ground if you have a multimeter
- Replace the oxygen sensor if its heater tests bad
- Clear codes and confirm the fault does not return
Estimated repair cost
$150 – $350
Upstream oxygen sensor bank 2: parts and labor
- Repair oxygen sensor wiring or connector$100 – $250
- Replace heater fuse and inspect circuit$20 – $120
- PCM or control circuit diagnosis/repair$150 – $400
Prices vary by vehicle, engine layout, sensor access, and local labor rates.
Frequently asked questions
Can I drive with P0155?
Usually yes for short trips, but get it checked soon. The engine may run slightly rich or less efficiently until the sensor heater works again.
Will P0155 fail an emissions test?
Yes, it often can. A check engine light and an inactive oxygen sensor heater commonly cause an inspection failure.
Is the oxygen sensor itself bad or just the wiring?
Either is possible. The sensor heater is the most common failure, but damaged wiring and blown fuses are also common.
Can I replace the sensor myself?
Sometimes, yes, if you can safely reach it and remove it without damaging the exhaust threads. On some vehicles it is easy, but rust and tight access can make the job difficult.
Why does the code come back after clearing it?
Because the underlying heater fault is still there. If the sensor heater, wiring, or fuse is not fixed, the computer will detect the problem again on the next cold start.
Related codes
Related problems
This guide covers most cars and is general advice, not an inspection. Prices are typical US independent-shop ranges and vary by region, car and shop. If your brakes, steering or a warning light feel unsafe, stop driving and contact a mechanic.